Need help?

EN 62196-1:2012/A11:2013 Standard

wave
Save  

  Keywords:

#accessories #iec #used #intended #use

This standard is superseded by:
  •   EN 62196-1:2014
  •   This standard is no longer addressed in the last official Journal publication of the "2025-07-22 ". This standard is addressed for the last time in the official journal publication of the "2018-09-14"

      Directive

    Low voltage (LVD) Directive (2014/35/EU)

      Last Official Journal reference

    Friday 14th of September 2018

      Description:

    Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements

      Purpose

    This part of IEC 62196 is applicable to plugs, socket-outlets, connectors, inlets and cable assemblies for electric vehicles (EV), herein referred to as “accessories”, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding - 690 V a.c. 50 Hz – 60 Hz, at a rated current not exceeding 250 A, - 1 500 V d.c. at a rated current not exceeding 400 A. These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851-1:2010 which operate at different voltages and frequencies and which may include ELV and communication signals. The accessories covered by this standard are intended only to be used with vehicles that comply with the requirements of 7.2.3.1 of IEC 61851-1:2010. These accessories and cable assemblies are to be used in an ambient temperature of between -30 °C and +50 °C. NOTE In some countries, other requirements may apply. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this standard are for use in certain modes of charging EVs. These modes are defined in IEC 61851-1:2010. These definitions and a description of the types of connection (cases A, B and C), also described in IEC 61851-1:2010, are reproduced herein as Annex A. This standard does not apply to those standardised accessories used in charging systems where the use of such accessories constructed to the requirements of other standards is permitted (e.g. in mode 1 and mode 2). Such standardized accessories may be used for those situations (mode and case) identified in IEC 61851-1:2010. This standard can be used as a guide for accessories with a lesser number of contacts and lower ratings for use with light duty vehicles.

      Publication

    Wednesday 20th of April 2016

      Cessation

    This standard has been withdrawn on 2019-10-06

      Amendment

    This standard is an amendment for "EN 62196-1:2012"

      Reference

    This standard supersedes the "EN 62196-1:2012/A12:2014"

    Anyway is still possible use the "EN 62196-1:2012/A12:2014" until October 15th, 2017

      Related Standards

    EN ISO 11252:2013

    Low voltage (LVD) Directive (2014/35/EU)

    Lasers and laser-related equipment - Laser device - Minimum requirements for documentation (ISO 11252:2013)

    EN 13637:2015

    Low voltage (LVD) Directive (2014/35/EU)

    Building hardware - Electrically controlled exit systems for use on escape routes - Requirements and test methods

    HD 308 S2:2001

    Low voltage (LVD) Directive (2014/35/EU)

    Identification of cores in cables and flexible cords

    HD 368 S1:1978

    Low voltage (LVD) Directive (2014/35/EU)

    Direct acting recording electrical measuring instruments and their accessories

    HD 549 S1:1989

    Low voltage (LVD) Directive (2014/35/EU)

    Conference systems - Electrical and audio requirements

    HD 597 S1:1992

    Low voltage (LVD) Directive (2014/35/EU)

    Coupling capacitors and capacitor dividers

      Stay up to date

    CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

    CELAB performs voluntary inspection activities on technical construction files to check their contents.

    CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

    CLICK HERE TO GET TESTS AND INFO ON THE EN 62196-1:2012/A11:2013 STANDARD

      ACCESS

    Search for a standard
    GO

    Register

    Already a member?
    Login

      OTHER APPLICATIONS

    If you are interested in DO160 tests, you can give a try to our other free of charge software:
    CE-Marking assistant, Version: 1.3.0