Need help?

EN 62196-2:2012/A11:2013 Standard

wave
Save  

  Keywords:

#used #standard #intended #specified #iec

This standard is superseded by:
  •   EN 62196-2:2012/A12:2014
  •   Directive

    Low voltage (LVD) Directive (2014/35/EU)

      Last Official Journal reference

    Wednesday 13th of December 2023

      Description:

    Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories

      Purpose

    This standard applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 500 V a.c., 50 to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This standard covers the basic interface accessories for vehicle supply as specified in IEC 62196-1, and intended for use in conductive charging systems for circuits specified in IEC 61851-1:2010. Electric vehicles covers all road vehicles, including plug-in hybrid road vehicles (PHEV), that derive all or part of their energy from on-board batteries. NOTE 1 These accessories may provide a contact that can be used for the proximity contact function. These accessories are intended to be used for circuits specified in IEC 61851-1:2010 which operate at different voltages and frequencies and which may include ELV and communication signals. These accessories may be used for bidirectional energy transmission (under consideration). This standard applies to the accessories to be used in an ambient temperature of between - 30 °C and + 50 °C. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. Vehicle inlet and vehicle connector to this standard are intended to be used for charging in modes 1, 2 and 3, cases B and C. The socket-outlets and plugs covered by this standard are intended to be used for charging mode 3 only, case A and B. The modes and permissible connections are specified in Part 1.

      Publication

    Wednesday 20th of April 2016

      Amendment

    This standard is an amendment for "EN 62196-2:2012"

      Reference

    This standard supersedes the "EN 62196-2:2012"

    Anyway is still possible use the "EN 62196-2:2012" until October 15th, 2017

      Related Standards

    EN 62368-1:2014/AC:2015

    Low voltage (LVD) Directive (2014/35/EU)

    Audio/video, information and communication technology equipment - Part 1: Safety requirements (IEC 62368-1:2014, modified)

    EN 61558-2-4:2009

    Low voltage (LVD) Directive (2014/35/EU)

    Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-4: Particular...

    EN 61557-7:2007

    Low voltage (LVD) Directive (2014/35/EU)

    Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or mo...

    EN 61557-8:2015

    Low voltage (LVD) Directive (2014/35/EU)

    Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or mo...

    EN 61557-10:2013

    Low voltage (LVD) Directive (2014/35/EU)

    Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or mo...

    EN 61557-11:2009

    Low voltage (LVD) Directive (2014/35/EU)

    Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or mo...

      Stay up to date

    CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

    CELAB performs voluntary inspection activities on technical construction files to check their contents.

    CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

    CLICK HERE TO GET TESTS AND INFO ON THE EN 62196-2:2012/A11:2013 STANDARD

      ACCESS

    Search for a standard
    GO

    Register

    Already a member?
    Login

      OTHER APPLICATIONS

    If you are interested in DO160 tests, you can give a try to our other free of charge software:
    CE-Marking assistant, Version: 1.3.0