Need help?

EN 303 135 V2.1.1 Standard

wave
Save  

  Keywords:

#18 #11 #transceiver #ghz #frequency

  Directive

Radio equipment Directive (2014/53/EU)

  Last Official Journal reference

Friday 4th of September 2026

  Description:

Electromagnetic compatibility and Radio spectrum Matters (ERM); Coastal Surveillance, Vessel Traffic Services and Harbour Radars (CS/VTS/HR); Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

  Purpose

Surveillance (CS) or Harbour Radar Systems with the following characteristics: • Utilizing modulated or unmodulated pulses. • Transmitter Peak Envelope Power up to 100 kW. • The transceiver-antenna connection is using a hollow metallic rectangular waveguide. • The antenna is rotating, waveguide- based and passive. • At the transceiver output an RF-circulator is used. NOTE 1: Since transceiver and antenna are hollow metallic rectangular waveguide based, the frequency range for measurements that needs to be addressed covers 6,56 GHz to 26 GHz. The lower limit of this frequency range is obtained as cut-off frequency of the combination of WR112/R84 taper section and a WR90/R100 Waveguide as defined by IEC 60153-2 [i.2]. The upper limit corresponds to the upper limit stated in ERC/Recommendation 74-01 [i.4]. Other types of waveguide may be used by the same principles to obtain complete measurement coverage of the frequency range of the output flange of the equipment under test. NOTE 2: Since at the transceiver output an RF circulator is used, it is assumed that the transceiver characteristics remain independent from the antenna. NOTE 3: According to article 5 of the ITU Radio Regulations [i.5] there are a number of bands between 8,5 GHz and 10 GHz that are allocated to Radiolocation service. There are national deviations to the detailed band usages, but the basic spectrum usage regulation is the same. Table 1: Radiolocation service frequency bands [GHz] 8 500 - 8 550 8 550 - 8 650 8 650 - 8 750 8 750 - 8 850 8 850 - 9 000 9 000 - 9 200 9 200 - 9 300 9 300 - 9 500 9 500 - 9 800 9 800 - 9 900 9 900 - 10 000 The present document contains requirements to demonstrate that "...radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" [i.1]. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive [i.1] may apply to equipment within the scope of the present document.

  Publication

Friday 13th of January 2017

  Cessation

This standard will be withdrawn on 2028-03-07

  Essential Requirement

Article 3(2)

  Related Standards

EN 50385:2017

Radio equipment Directive (2014/53/EU)

Product standard to demonstrate the compliance of base station equipment with radiofrequency electromagnetic field exposure limits...

EN 301 406-2 V3.1.1

Radio equipment Directive (2014/53/EU)

Digital Enhanced Cordless Telecommunications (DECT); Harmonised Standard for access to radio spectrum; Part 2: DECT-2020 NR

EN 303 661 V1.1.1

Radio equipment Directive (2014/53/EU)

Short Range Devices (SRD); Ground Based Synthetic Aperture Radar (GBSAR) in the frequency range 17,1 GHz to 17,3 GHz and High Defi...

EN 301 908-25 V15.1.1

Radio equipment Directive (2014/53/EU)

IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 25: New Radio (NR) User Equipment (UE); Release 15

EN 301 908-24 V15.1.1

Radio equipment Directive (2014/53/EU)

IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 24: New Radio (NR) Base Stations (BS); Release 15

EN 301 908-23 V15.1.1

Radio equipment Directive (2014/53/EU)

IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 23: Active Antenna System (AAS) Base Station (BS); R...

  Stay up to date

CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

CELAB performs voluntary inspection activities on technical construction files to check their contents.

CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

CLICK HERE TO GET TESTS AND INFO ON THE EN 303 135 V2.1.1 STANDARD

  ACCESS

Search for a standard
GO

Register

Already a member?
Login

  OTHER APPLICATIONS

If you are interested in DO160 tests, you can give a try to our other free of charge software:
CE-Marking assistant, Version: 1.3.0