Need help?

EN 303 213-6-1 V3.1.1 Standard

wave
Save  

  Keywords:

#mhz #transceiver #note #antenna #frequency

  Directive

Radio equipment Directive (2014/53/EU)

  Last Official Journal reference

Friday 1st of December 2023

  Description:

Advanced Surface Movement Guidance and Control System (A-SMGCS); Part 6: Harmonised Standard for access to radio spectrum for deployed surface movement radar sensors; Sub-part 1: X-band sensors using pulsed signals and transmitting power up to 100 kW

  Purpose

The present document specifies technical characteristics and methods of measurements for monostatic X-band radar sensors intended for the surveillance of airport surface movement traffic with the following characteristics: • Operating in one or both of the following frequency ranges: - 9 000 MHz to 9 200 MHz and 9 300 MHz to 9 500 MHz utilizing modulated or unmodulated pulses. • Transmitter Peak Envelope Power up to 100 kW. • The transceiver-antenna connection is using a hollow metallic rectangular waveguide. • The antenna is rotating, waveguide-based and passive. • At the transceiver output an RF-circulator is used. NOTE 1: Since transceiver and antenna are hollow metallic rectangular waveguide based the frequency range for measurements that needs to be addressed covers 6,56 GHz to 26 GHz. The lower limit of this frequency range is obtained as cut-off frequency of the combination of WR112/R84 taper section and a WR90/R100 Waveguide IEC 60153-2. The upper limit corresponds to the upper limit stated in table 1 of ERC Recommendation 74-01. NOTE 2: Since at the transceiver output an RF circulator is used, it is assumed that the transceiver characteristics remain independent from the antenna. NOTE 3: Aeronautical Surface Movement Radars covered by the present document are expected to use the bands 9 000 MHz to 9 200 MHz and/or 9 300 MHz to 9 500 MHz. According article 5 of the ITU Radio Regulations the band 9 000 MHz to 9 200 MHz is allocated to the Aeronautical Radionavigation Service on a primary basis and the band 9 300 MHz to 9 500 MHz is allocated to the Radionavigation Service on a primary basis. NOTE 4: The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU is given in annex A.

  Publication

Tuesday 27th of October 2020

  Reference

This standard supersedes the "EN 303 213-6-1 V2.1.1"

  Related Standards

EN 50360:2017

Radio equipment Directive (2014/53/EU)

Product standard to demonstrate the compliance of wireless communication devices, with the basic restrictions and exposure limit v...

EN 300 674-2-1 V3.1.1

Radio equipment Directive (2014/53/EU)

Transport and Traffic Telematics (TTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s...

EN 302 245 V2.2.1

Radio equipment Directive (2014/53/EU)

Transmitting equipment for the Digital Radio Mondiale (DRM) service; Harmonised Standard for access to radio spectrum

EN 302 077 V2.3.1

Radio equipment Directive (2014/53/EU)

Transmitting equipment for the Digital Audio Broadcasting (DAB) service; Harmonised Standard for access to radio spectrum

EN 301 908-1 V15.2.1

Radio equipment Directive (2014/53/EU)

IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 1: Introduction and common requirements; Release 15

EN 301 489-52 V1.2.1

Radio equipment Directive (2014/53/EU)

ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;Part 52: Specific conditions for Cellular Communicat...

  Stay up to date

CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

CELAB performs voluntary inspection activities on technical construction files to check their contents.

CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

CLICK HERE TO GET TESTS AND INFO ON THE EN 303 213-6-1 V3.1.1 STANDARD

  ACCESS

Search for a standard
GO

Register

Already a member?
Login

  OTHER APPLICATIONS

If you are interested in DO160 tests, you can give a try to our other free of charge software:
CE-Marking assistant, Version: 1.3.0