Need help?

EN 302 208 V3.3.1 Standard

wave
Save  

  Keywords:

#frequency #eu #present #document #mhz

  Directive

Radio equipment Directive (2014/53/EU)

  Last Official Journal reference

Friday 1st of December 2023

  Description:

Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to 4 W; Harmonised Standard for access to radio spectrum

  Purpose

The present document specifies technical characteristics and methods of measurements for Radio Frequency Identification (RFID) devices used in the frequency ranges 865 MHz to 868 MHz and 915 MHz to 921 MHz. Power limits up to a maximum of 2 W e.r.p. are specified for this equipment in the frequency band 865 MHz to 868 MHz and up to a maximum of 4 W e.r.p. in the frequency band 915 MHz to 921 MHz. NOTE 1: The term frequency band is typically used for reference to dedicated bands as described in CEPT/ERC/REC 70-03, while frequency range is used in the other cases. The frequency usage conditions for RFID are EU wide harmonised in the band 865 MHz to 868 MHz according to [Commission implementing Decision (EU) 2017/1483] and in the band 915 MHz to 921 MHz according to [Commission Implementing Decision (EU) 2018/1538]. According to [Commission Implementing Decision (EU) 2018/1538] EU member states are requested to implement 3 channels only in the 915 MHz to 921 MHz band. It should be noted that the frequency band 915 MHz to 921 MHz has only a limited implementation status within the European Union and the CEPT countries. CEPT/ERC/REC 70-03 provides in appendix 1 an overview of countries where the band is implemented. The present document applies to RFID interrogators and tags operating together as a system. For each specified band, multiple high power channels are made available for use by interrogators. The tags respond with a modulated signal preferably in the adjacent low power channels. Interrogators may be used with either integral or external antennas. The types of equipment covered by the present document are as follows: • fixed interrogators; • portable interrogators; • batteryless tags; • battery assisted tags; • battery powered tags. These types of radio equipment are capable of operating in the frequency ranges given in table 1 and table 2. The present document contains requirements to demonstrate that the specified radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. NOTE 2: The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU is given in annex A.

  Publication

Tuesday 20th of July 2021

  Related Standards

EN 50360:2017

Radio equipment Directive (2014/53/EU)

Product standard to demonstrate the compliance of wireless communication devices, with the basic restrictions and exposure limit v...

EN 303 345-2 V1.2.1

Radio equipment Directive (2014/53/EU)

Broadcast Sound Receivers; Part 2: AM broadcast sound service; Harmonised Standard for access to radio spectrum

EN 301 489-12 V3.2.1

Radio equipment Directive (2014/53/EU)

ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 12: Specific conditions for Very Small Apertur...

EN 301 025 V2.3.1

Radio equipment Directive (2014/53/EU)

VHF radiotelephone equipment for general communications and associated equipment for Class "D" Digital Selective Calling...

EN 300 674-2-1 V3.1.1

Radio equipment Directive (2014/53/EU)

Transport and Traffic Telematics (TTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s...

EN 303 347-3 V2.1.1

Radio equipment Directive (2014/53/EU)

Meteorological Radars; Harmonised Standard for access to radio spectrum; Part 3: Meteorological Radar Sensor operating in the freq...

  Stay up to date

CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

CELAB performs voluntary inspection activities on technical construction files to check their contents.

CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

CLICK HERE TO GET TESTS AND INFO ON THE EN 302 208 V3.3.1 STANDARD

  ACCESS

Search for a standard
GO

Register

Already a member?
Login

  OTHER APPLICATIONS

If you are interested in DO160 tests, you can give a try to our other free of charge software:
CE-Marking assistant, Version: 1.3.0