Need help?

EN 301 908-2 V11.1.1 Standard

wave
Save  

  Keywords:

#mhz #transmit #receive #document #present

This standard is superseded by:
  •   EN 301 908-2 V11.1.2
  •   This standard is no longer addressed in the last official Journal publication of the "2023-12-01 ". This standard is addressed for the last time in the official journal publication of the "2018-09-14"

      Directive

    Radio equipment Directive (2014/53/EU)

      Last Official Journal reference

    Friday 14th of September 2018

      Description:

    IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

      Purpose

    The present document applies to the following radio equipment type: • User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: UTRA FDD operating bands UTRA FDD Band Direction of transmission UTRA FDD operating bands I Transmit 1 920 MHz to 1 980 MHz Receive 2 110 MHz to 2 170 MHz III Transmit 1 710 MHz to 1 785 MHz Receive 1 805 MHz to 1 880 MHz VII Transmit 2 500 MHz to 2 570 MHz Receive 2 620 MHz to 2 690 MHz VIII Transmit 880 MHz to 915 MHz Receive 925 MHz to 960 MHz XV Transmit 1 900 MHz to 1 920 MHz Receive 2 600 MHz to 2 620 MHz XVI Transmit 2 010 MHz to 2 025 MHz Receive 2 585 MHz to 2 600 MHz XX Transmit 832 MHz to 862 MHz Receive 791 MHz to 821 MHz XXII Transmit 3 410 MHz to 3 490 MHz Receive 3 510 MHz to 3 590 MHz The present document covers requirements for UTRA FDD User Equipment from 3GPP™ Releases 99, 4, 5, 6, 7, 8, 9, 10 and 11 defined in ETSI TS 125 101 [4]. This include the requirements for UE operating bands from 3GPP™ Release 12 defined in ETSI TS 125 101 [4]. In addition, the present document covers requirements for UTRA FDD User Equipment in the operating bands specified in ETSI TS 102 735 [i.4]. NOTE: For Band XX: - for user equipment designed to be mobile or nomadic, the requirements in the present document measured at the antenna port also show conformity to the corresponding requirement defined as TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7] and CEPT Report 30 [i.8]; - for user equipment designed to be fixed or installed, the present document does not address the requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7] and CEPT Report 30 [i.8]. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.

      Publication

    Wednesday 12th of April 2017

      Cessation

    This standard has been withdrawn on 2019-02-28

      Essential Requirement

    Article 3(2)

      Related Standards

    EN 50360:2017

    Radio equipment Directive (2014/53/EU)

    Product standard to demonstrate the compliance of wireless communication devices, with the basic restrictions and exposure limit v...

    EN 303 204 V3.1.1

    Radio equipment Directive (2014/53/EU)

    Fixed Short Range Devices (SRD) in data networks; Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power ...

    EN 301 908-2 V13.1.1

    Radio equipment Directive (2014/53/EU)

    IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

    EN 303 213-5-1 V1.1.1

    Radio equipment Directive (2014/53/EU)

    Advanced Surface Movement Guidance and Control System (A-SMGCS); Part 5: Harmonised Standard for access to radio spectrum for Mult...

    EN 301 908-13 V13.1.1

    Radio equipment Directive (2014/53/EU)

    IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 13: Evolved Universal Terrestrial Radio Access (E-UT...

    EN 303 213-6-1 V3.1.1

    Radio equipment Directive (2014/53/EU)

    Advanced Surface Movement Guidance and Control System (A-SMGCS); Part 6: Harmonised Standard for access to radio spectrum for depl...

      Stay up to date

    CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

    CELAB performs voluntary inspection activities on technical construction files to check their contents.

    CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

    CLICK HERE TO GET TESTS AND INFO ON THE EN 301 908-2 V11.1.1 STANDARD

      ACCESS

    Search for a standard
    GO

    Register

    Already a member?
    Login

      OTHER APPLICATIONS

    If you are interested in DO160 tests, you can give a try to our other free of charge software:
    CE-Marking assistant, Version: 1.3.0