Need help?

EN 15001-1:2023 Standard

wave
Save  

  Keywords:

#gas #standard #european #standard #ped

  Directive

Pressure equipment Directive (2014/68/EU)

  Last Official Journal reference

Monday 12th of January 2026

  Description:

Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing

  Purpose

This European Standard specifies detailed functional requirements for the design, selection of materials, construction, inspection and testing of: - industrial gas installation pipework and assemblies with an operating pressure greater than 0,5 bar; and - non-industrial gas installation pipework (residential and commercial) with an operating pressure greater than 5 bar in buildings; starting from the outlet of the network operator’s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This standard also covers the pipework to the inlet connection of a gas appliance that is not included within the scope of the appliance standard. NOTE 1 The use of the term installation and pipework is interchangeable. Apart from the exceptions stated below, this standard applies to gas installations operating at ambient temperatures between −20 °C and 40 °C and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 (all parts) for metallic pipework. For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar in buildings, EN 1775 applies. For gas installations that do not fall within the scope of EN 1775 or other European Standards, this standard applies. In this European Standard, the term “gas“ refers to combustible gases, which are gaseous at 15 °C and 1 013 mbar absolute atmospheric pressure (normal conditions). These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases as classified in EN 437:2003+A1:2009, Table 1. The given values are considered as normal conditions for all volumes given in this standard. This European Standard is applicable to installation pipework for the carriage of: - processed, non-toxic and non-corrosive natural gas according to EN 437:2003+A1:2009 and EN 16726 "Gas infrastructure - Quality of gas - Group H"; - vaporized LPG; - biomethane, complying with EN 16723 1; - vaporized LNG. NOTE 2 The specification of vaporized LNG is equal to that of natural gas as classified in EN 437:2003+A1:2009. This European Standard does not cover pipework for hydrogen rich gases that fall outside the definitions within EN 437:2003+A1:2009. LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure in the liquid state (e.g. between the storage vessel and any pressure regulator). In this standard, all pressures are gauge pressures unless otherwise stated. This standard has been harmonized to address the essential safety requirements of the Pressure Equipment Directive (PED, 2014/68/EU [formerly 97/23/EC]) relevant for the joining of gas installation pipework (assemblies) falling within the scope of the PED. These are listed in Annex ZA. However, "this Directive does not cover the assembly of pressure equipment on the site and under the responsibility of the user, as in the case of industrial installations" (PED, Preamble, 7th recital, last paragraph). Although in this respect, the standard takes into account the essential safety requirements of the PED, no inference can be drawn from this as to whether or not the installation or parts of the installation falls within the scope of the PED. Reference should therefore be made to the PED and relevant national legislation. This European Standard specifies common basic principles for gas supply systems. Users of this European Standard should be aware (...)

  Publication

Friday 31st of January 2025

  Related Standards

EN 378-2:2016

Pressure equipment Directive (2014/68/EU)

Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and ...

EN 10216-4:2013

Pressure equipment Directive (2014/68/EU)

Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 4: Non-alloy and alloy steel tubes with specifie...

EN 14382:2005+A1:2009/AC:2009

Pressure equipment Directive (2014/68/EU)

Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 ...

EN 14394:2005+A1:2008

Pressure equipment Directive (2014/68/EU)

Heating boilers - Heating boilers with forced draught burners - Nominal heat output not exceeding 10 MW and maximum operating temp...

EN 15776:2011+A1:2015

Pressure equipment Directive (2014/68/EU)

Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cas...

EN 16668:2016+A1:2018

Pressure equipment Directive (2014/68/EU)

Industrial valves - Requirements and testing for metallic valves as pressure accessories

  Stay up to date

  ACCESS

Search for a standard
GO

Register

Already a member?
Login

  OTHER APPLICATIONS

If you are interested in DO160 tests, you can give a try to our other free of charge software:
CE-Marking assistant, Version: 1.3.0