Need help?

EN 303 204 V2.1.2 Standard

wave
Save  

  Keywords:

#srds #bands #network #intended #use

  This standard is no longer addressed in the last official Journal publication of the "2023-12-01 ". This standard is addressed for the last time in the official journal publication of the "2022-11-11"

  Directive

Radio equipment Directive (2014/53/EU)

  Last Official Journal reference

Friday 11th of November 2022

  Description:

Network Based Short Range Devices (SRD); Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

  Purpose

The present document applies to the following radio equipment types: 1) Network Based SRDs which are SRDs intended to operate in association with other SRDs to form network topologies supporting the intended application. 2) Network Relay Points which are specific Network Based SRDs supporting interconnection of a network of SRDs with an external network or service. These radio equipment types are capable of operating in all or any part of the frequency bands given in Table 1a. Table 1a: Frequency bands designated to Network Based Short Range Devices Network Based SRD frequency bands Transmit 870,00 MHz to 875,6 MHz Receive 870,00 MHz to 875,6 MHz NOTE 1: The availability of the frequency band in Table 1a in European Union and CEPT countries can be obtained from the EFIS (http://www.efis.dk/) and is also listed in Appendices 1 and 3 of REC 70-03 [i.2]. NOTE 2: In addition, it should be noted that other frequency bands may be available for network based short range devices in a country. See National Radio Interfaces (NRI) as relevant for additional guidance. NOTE 3: On non-harmonized parameters, national administrations may impose certain conditions such as the type of modulation, frequency, channel/frequency separations, maximum transmitter radiated power, duty cycle, and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of Individual Rights for use of spectrum or General Authorization, or as a condition for use under "licence exemption" as it is in most cases for Short Range Devices. The present document covers equipment intended for use in a fixed location, equipment normally fixed in a vehicle and equipment intended to be carried or attached. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.

  Publication

Friday 11th of November 2016

  Cessation

This standard has been withdrawn on 2023-01-20

  Essential Requirement

Article 3(2)

  Related Standards

EN 50360:2017

Radio equipment Directive (2014/53/EU)

Product standard to demonstrate the compliance of wireless communication devices, with the basic restrictions and exposure limit v...

EN 302 208 V3.3.1

Radio equipment Directive (2014/53/EU)

Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W and in the band 915 ...

EN 301 444 V2.2.1

Radio equipment Directive (2014/53/EU)

Satellite Earth Stations and Systems (SES); Land Mobile Earth Stations (LMES) and Maritime Mobile Earth Stations (MMES) providing ...

EN 303 758 V1.1.1

Radio equipment Directive (2014/53/EU)

TETRA radio equipment using non-constant envelope modulation operating in a channel bandwidth of 25 kHz, 50 kHz, 100 kHz or 150 kH...

EN 303 413 V1.2.1

Radio equipment Directive (2014/53/EU)

Satellite Earth Stations and Systems (SES); Global Navigation Satellite System (GNSS) receivers; Radio equipment operating in the ...

EN 303 372-2 V1.2.1

Radio equipment Directive (2014/53/EU)

Satellite Earth Stations and Systems (SES); Satellite broadcast reception equipment; Part 2: Indoor unit

  Stay up to date

CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

CELAB performs voluntary inspection activities on technical construction files to check their contents.

CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

CLICK HERE TO GET TESTS AND INFO ON THE EN 303 204 V2.1.2 STANDARD

  ACCESS

Search for a standard
GO

Register

Already a member?
Login

  OTHER APPLICATIONS

If you are interested in DO160 tests, you can give a try to our other free of charge software:
CE-Marking assistant, Version: 1.3.0