Need help?

EN IEC 61010-2-091:2021/A11:2021 Standard

wave
Save  

  Keywords:

#radiation #equipment #intended #new #paragraph

  Directive

Low voltage (LVD) Directive (2014/35/EU)

  Last Official Journal reference

Wednesday 13th of December 2023

  Description:

Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-091: Particular requirements for cabinet X-ray systems

  Purpose

1 Scope and objectThis clause of Part 1 is applicable, except as follows:1.1 Scope1.1.1 Equipment included in scopeDeletion:Delete the first paragraph.Replacement:Replace the second paragraph (above items a) to c)) with the following new text:This part of IEC 61010 specifies particular safety requirements for cabinet X-ray systems, which fall under any of categories a), b) or c) below.Addition:Add the two following new paragraphs at the end of the subclause:Equipment covered by this document can be both PROTECTED EQUIPMENT or PARTIALLY PROTECTED EQUIPMENT, with X-ray generator voltage up to 500 kV.A cabinet X-ray system is a system that contains an X-ray tube installed in a cabinet, which, independently of existing architectural structures except the floor on which it may be placed, isintended to contain at least that portion of a material being irradiated, provide radiation attenuation and prevent operator access to the radiation beam, during generation of X-radiation.These cabinet X-ray systems are used in industrial, commercial, and public environments, for example, to inspect materials, to analyse materials, and to screen baggage.1.1.2 Equipment excluded from scopeAddition:Add the following new items to the list:aa) Equipment intended to apply X-radiation to humans or animals;bb) Equipment incorporating an X-ray tube but not incorporating complete shielding againstX-radiation HAZARDS, such as:– equipment intended to be used within a shielded room which excludes personnel during operation;– equipment intended to be used with separate portable or temporary shielding;– equipment intended to produce an emerging beam of X-radiation.1.2 Object1.2.1 Aspects included in scopeAddition:Add the following new text to the end of the first paragraph:This part of IEC 61010 specifies requirements for the design and methods of construction of cabinet X-ray systems to provide adequate protection for OPERATORS, bystanders, trained service personnel and the surrounding area against unintentionally-emitted X-radiation and from mechanical HAZARDS related to their conveyors.

  Publication

Tuesday 10th of May 2022

  Amendment

This standard is an amendment for "EN IEC 61010-2-091:2021"

  Related Standards

EN 62626-1:2014

Low voltage (LVD) Directive (2014/35/EU)

Low-voltage switchgear and controlgear enclosed equipment - Part 1: Enclosed switch-disconnectors outside the scope of IEC 60947-...

EN 61010-2-020:2006

Low voltage (LVD) Directive (2014/35/EU)

Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-020: Particular requirements fo...

EN 60998-2-3:2004

Low voltage (LVD) Directive (2014/35/EU)

Connecting devices for low-voltage circuits for household and similar purposes - Part 2-3: Particular requirements for connecting ...

EN 60999-1:2000

Low voltage (LVD) Directive (2014/35/EU)

Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1:...

EN 60999-2:2003

Low voltage (LVD) Directive (2014/35/EU)

Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2:...

EN 61008-2-1:1994

Low voltage (LVD) Directive (2014/35/EU)

Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB's) - Part ...

  Stay up to date

CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

CELAB performs voluntary inspection activities on technical construction files to check their contents.

CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

CLICK HERE TO GET TESTS AND INFO ON THE EN IEC 61010-2-091:2021/A11:2021 STANDARD

  ACCESS

Search for a standard
GO

Register

Already a member?
Login

  OTHER APPLICATIONS

If you are interested in DO160 tests, you can give a try to our other free of charge software:
CE-Marking assistant, Version: 1.3.0