Need help?

EN 303-5:2021+A1:2022 Standard

wave
Save  

  Keywords:

#european #standard #heating #safety #wood

  Directive

Machinery (MD) Directive (2006/42/EC)

  Last Official Journal reference

Wednesday 2nd of August 2023

  Description:

Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking

  Purpose

1.1 General This European Standard applies to heating boilers including safety devices up to a nominal heat output of 500 kW which are designed for the burning of solid fuels only and are operated according to the instructions of the boiler manufacturer. This European Standard deals with significant hazards, hazardous situations and events relevant to heating boilers used as intended and under the conditions foreseen by the manufacturer (see Clause 4). The boilers may operate under natural draught or forced draught. The stoking may work manually or automatically. The boilers may operate under room sealed conditions in case of supervised under pressure in the combustion chamber. The boilers may operate in condensing condition. NOTE This European Standard deals with boilers which are both within and outside of the scope of the Machinery Directive 2006/42/EC. This European Standard contains requirements and test methods for safety, combustion quality, operating characteristics, marking and maintenance of heating boilers and secondary emission reduction appliances and efficiency improvement appliances. It also covers all external equipment that influences the safety systems (e.g. back burning safety device, integral fuel hopper). This European Standard covers only boilers that include burners as a unit. The standard applies to the combination of a boiler body with a solid fuel burner according to EN 15270 as a unit only when the whole unit is tested in accordance with this European Standard. Heating boilers in accordance with this European Standard are designed for central heating installations where the heat carrier is water and the maximum allowable temperature is 110 °C, and which can operate at a maximum allowable operating pressure of 6 bars. For heating boilers with a built-in or attached water heater (storage or continuous flow heater), this European Standard only applies to those parts of the water heater which are necessarily subject to the operating conditions of the heating boiler (heating part). This European Standard does not apply to: heating boilers and other heating appliances which are also designed for the direct heating of the place of installation; cooking appliances; the design and construction of external fuel storage and transportation devices prior to the safety devices of the boiler; room sealed applications above a nominal heat output > 70 kW or operated with positive pressure in the combustion chamber or operated under natural draught; This European Standard specifies the necessary terminology for solid fuel heating boilers, the control and safety related requirements, the design requirements, the technical heating requirements (taking into account the environmental requirements) and testing, as well as the marking requirements. This European Standard is not applicable to heating boilers which are tested before the date of its publication as an EN (European Standard). 1.2 Fuels These boilers may burn either fossil fuels, biogenic fuels or other fuels such as peat, as specified for their use by the boiler manufacturer, in accordance with the requirements of this European Standard. Solid fuels included in this European Standard are categorised as follows. 1.2.1 Biogenic fuels Biomass in a natural state, in the form of: Adaptation to new fuels standards and consideration of new fuels standards in preparation. A log wood with moisture content w ≤ 25 %, according to EN 14961-5; B1 chipped wood (wood chipped by machine, usually up to a maximum length of 15 cm) with moisture content from w 15 % to w 35 %, according to EN 14961-4; B2 chipped wood as under B1, except with moisture content w > 35 %; C1 compressed wood (e.g. pellets without additives, made of wood and/or bark particles; natural binding agents such as molasses, vegetable paraffins and starch are permitted), pellets according to EN 14961-2; (...)

  Publication

Wednesday 2nd of August 2023

  Amendment

This standard is an amendment for "EN 303-5:2021"

  Related Standards

EN 60745-2-18:2009

Machinery (MD) Directive (2006/42/EC)

Hand-held motor-operated electric tools - Safety - Part 2-18: Particular requirements for strapping tools

EN ISO 5395-2:2013/A2:2017

Machinery (MD) Directive (2006/42/EC)

Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 2: Pedestrian-controlled lawnmowers (ISO 53...

EN ISO 10218-1:2011

Machinery (MD) Directive (2006/42/EC)

Robots and robotic devices - Safety requirements for industrial robots - Part 1: Robots (ISO 10218-1:2011)

EN ISO 8528-13:2016

Machinery (MD) Directive (2006/42/EC)

Reciprocating internal combustion engine driven alternating current generating sets - Part 13: Safety (ISO 8528-13:2016, Corrected...

EN ISO 8230-3:2008

Machinery (MD) Directive (2006/42/EC)

Safety requirements for dry-cleaning machines - Part 3: Machines using combustible solvents (ISO 8230-3:2008)

EN ISO 8230-2:2008

Machinery (MD) Directive (2006/42/EC)

Safety requirements for dry-cleaning machines - Part 2: Machines using perchloroethylene (ISO 8230-2:2008)

  Stay up to date

CELAB is Notified Body No.2037 for the EMC Directive and Italian office of a Notified Body for the RED Directive.

CELAB performs voluntary inspection activities on technical construction files to check their contents.

CELAB can accomplish all the required tests in order to affix the CE-marking related to EMC, LVD, RED, MDD, machines and many others.

CLICK HERE TO GET TESTS AND INFO ON THE EN 303-5:2021+A1:2022 STANDARD

  ACCESS

Search for a standard
GO

Register

Already a member?
Login

  OTHER APPLICATIONS

If you are interested in DO160 tests, you can give a try to our other free of charge software:
CE-Marking assistant, Version: 1.3.0